LQ - Light Sources

 Download this chapter

LQ-0020 Green (532 nm) DPSSL in ø25 housingA green (532 nm ) emitting DPSSL is integrated into a C25 housing and is operated  with the “DC-0020 LED and Photodiode Controller”  The output power is < 5 mW. The diode laser is connected via a 15 pin SubD HD connector to the controller MK1. Inside the connector an EEPROM contains the data of the laser diode and when connected to the controller, these data are read and displayed by the controller.LQ-0020 Green (532 nm) DPSSL in ø25 housing

LQ-0030 Green (532)  pilot laser with USB power supplyA green (532 nm ) emitting DPSSL is integrated into a C25 housing and is operated  by a 5 V wall plug power supply which is connected via a USB and 1.3 mm connector. The output power is < 5 mW.LQ-0030 Green (532)  pilot laser with USB power supply

LQ-0040 Green (532 nm) stabilized Laser, 40 mWIn connection with the controller MK1-HP this laser module emits maximum 40 mW tunable 532 nm radiation in single mode with a frequency stability of ±45 MHz. The green emitting DPSSL is mounted between two Peltier elements and the laser head is mounted into a 4 axes adjustment holder. Four precise fine pitch screws of repetitious accuracy allow the translational and azimuthal adjustment. The laser is connected to the controller with the 15 pin SubD HD connector which  contains an EEPROM where the parameters of the laser are stored. The controller reads the data and sets the critical values accordingly.LQ-0040 Green (532 nm) stabilized Laser, 40 mW

LQ-0060 Red (635 nm) diode laser in ø 25 housingA laser diode emitting 3 mW is mounted into a housing (C25) with 25 mm diameter. The two grooves are provided for a defined position inside a mounting plate (C25). The adjustable collimator can be removed if not required. The laser diode is powered by connecting it via the 1.3 mm jack at the rear to the provided 5 V power supply including the 1.3 mm to USB cable.LQ-0060 Red (635 nm) diode laser in ø 25 housing

LQ-0100 Neon spectral lampThis small but very effective module contains a Neon lamp which is operated at 230 VAC with a few Nanoamperes only. It is contained in a C25 housing with a SM fibre connector to allow the direct connection to a fibre coupled spectrometer. The Neon lamps emits the well known atomic lines and thus serves as a calibration source. An adapter is provided to connect the lamp to the mains line.LQ-0100 Neon spectral lamp

LQ-0200 White LED in ø 25 HousingA high power white light LED with an emission surface of less 2 millimetre is contained into in a C25 housing. The LED is located closely to the front which has an opening of 2 mm. Furthermore a current stabilizer is integrated as well into the housing. At the rear of the housing a 1.3 mm jack is located for the power supply. For the operation a 5V power supply as well as a 1.3 mm to USB connection cable is provided. However the LED can be operated also from other sources from 3.5 V to 16 V DC.LQ-0200 White LED in ø 25 Housing

LQ-0210 Red LED in ø 25 housingA high power red (635 nm peak) light LED with an emission surface of less 2 millimetre is contained into in a C25 housing. The LED is located closely to the front which has an opening of 2 mm. Furthermore a current stabilizer is integrated as well into the housing. At the rear of the housing a 1.3 mm jack is located for the power supply. For the operation a 5V power supply as well as a 1.3 mm to USB connection cable is provided. However the LED can be operated also from other sources from 3.5 V to 16 V DC.LQ-0210 Red LED in ø 25 housing

LQ-0212 Red LED in C25 with fibre jackA high power red (635 nm peak) light LED with an emission surface of less 2 millimetre is contained into in a C25 housing. The LED is located closely to the front which has a fibre ST. For the operation the DC-0030 Dual channel LED transmitter is provided. However the LED can be operated also from other sources via the 2.1 mm connector, not exceeding the maximum current of 700 mA.LQ-0212 Red LED in C25 with fibre jack

LQ-0214 Dark Red LED in ø 25 housingA high power dark red (670 nm peak) light LED with an emission surface of less 2 millimetre is contained into in a C25 housing. The LED is located closely to the front which has an opening of 2 mm. Furthermore a current stabilizer is integrated as well into the housing. At the rear of the housing a 1.3 mm jack is located for the power supply. For the operation a 5V power supply as well as a 1.3 mm to USB connection cable is provided. However the LED can be operated also from other sources from 3.5 V to 16 V DC. LQ-0214 Dark Red LED in ø 25 housing

LQ-0220 Green LED in ø C25 housingA high power green (525 nm peak) light LED with an emission surface of less 2 millimetre is contained into in a C25 housing. The LED is located closely to the front which has an opening of 2 mm. Furthermore a current stabilizer is integrated as well into the housing. At the rear of the housing a 1.3 mm jack is located for the power supply. For the operation a 5V power supply as well as a 1.3 mm to USB connection cable is provided. However the LED can be operated also from other sources from 3.5 V to 16 V DC.LQ-0220 Green LED in ø C25 housing

LQ-0222 Green LED in C25 with fibre jackA high power green (525 nm peak) light LED with an emission surface of less 2 millimetre is contained into in a C25 housing. The LED is located closely to the front which has a fibre ST. For the operation the DC-0030 Dual channel LED transmitter is provided. However the LED can be operated also from other sources via the 2.1 mm connector, not exceeding the maximum current of 700 mA.LQ-0222 Green LED in C25 with fibre jack

LQ-0230 Blue LED in ø 25 housingA high power blue (470 nm peak) light LED with an emission surface of less 2 millimetre is contained into in a C25 housing. The LED is located closely to the front which has an opening of 2 mm. Furthermore a current stabilizer is integrated as well into the housing. At the rear of the housing a 1.3 mm jack for the power supply is located. For the operation a 5V power supply as well as a 1.3 mm to USB connection cable is provided. However the LED can be operated also from other sources from 3.5 V to 16 V DC.LQ-0230 Blue LED in ø 25 housing

LQ-0250 NIR LED in ø 25 housingA high power near infrared  (850 nm peak) light LED with an emission surface of less 2 millimetre is contained into in a C25 housing. The LED is located closely to the front which has an opening of 2 mm. Furthermore a current stabilizer is integrated as well into the housing. At the rear of the housing a 1.3 mm jack for the power supply is located. For the operation a 5V power supply as well as a 1.3 mm to USB connection cable is provided. However the LED can be operated also from other sources from 3.5 V to 16 V DC.LQ-0250 NIR LED in ø 25 housing

LQ-0300 Two mode HeNe laser Ø30 housing, 632 nmA helium Neon tube with a length of 18 cm is integrated into a black anodized aluminium housing with a diameter of 30 mm. Click grooves are applied to accommodate the tube in a C30 mounting plate or in two XY adjustment mounts (MM-0470 ). The laser beam is precisely centred to the mechanical axis of the tube. The laser emits an output power of 1.5 mW at a wavelength of 632 nm and two orthogonal modes with a mode spacing of 900 MHz. For the operation of the tube the power supply DC-0062 is required.LQ-0300 Two mode HeNe laser Ø30 housing, 632 nm

LQ-0350 Pulsed diode laser in housingThis diode laser emits pulsed radiation only when it is connected to the controller DC-0050 (<?>). The controller provides the necessary voltage to load the ignition condenser inside the laser head and the discharge pulse to release the laser pulse. The emission wavelength is 905 nm with a repetition rate of 2 kHz and an adjustable pulse width of 50 to 150 ns and a output energy of 4 µJ.LQ-0350 Pulsed diode laser in housing

LQ-0410 Energy saving lamp GU10, 9W/230VThe energy saving lamp has a GU10 socket and fits into the socket which is attached to a MG65 carrier. The electrical power is 9W at 230 VAC. The lamp is connected to the mains via a cable with an in line switch. The lamp emits radiation with a colour temperature of 6500 K.LQ-0410 Energy saving lamp GU10, 9W/230V

LQ-0440 Tungsten filament white light sourceA tungsten filament lamp is mounted into a 25 mm housing. The bulb has a diameter of 2.5 mm and fits into on side of a FSMA fibre jack. The lamp is connected via 6 wires to the controller (DC-0270 Filament and LED lamp controller, <?>). Two are used to power the lamp, two are used to measure the voltage at the lamp and two are used to measure the cold temperature of the lamp with a precise NTC resistor.LQ-0440 Tungsten filament white light source

LQ-0450 Tungsten lamp, GU10, 10 W/230VThe tungsten lamp has a GU10 socket and fits into the socket which is attached to a MG65 carrier. The electrical power is 10W at 230 VAC. The lamp is connected to the mains via a cable with an in line switch.LQ-0450 Tungsten lamp, GU10, 10 W/230V

Flag of Germany